My Profile

Keep Up to Date:
Blog RSS
Blog
Forum RSS
Forum

frame

...odwood Revival, the Earls Court Motor Show will enable the event to break out of its ‘period' time frame and display post-1966 vehicles. The effect will be like walking into a Tardis, offering o...
... American highways boast such features as: Quick-acting hydraulic or electric brakes; channel steel underframes; rugged bodies of oak, elm and airplane spruce; steel-clad plywood walls; spun glass or ...
... based on a Ford V8, and the aerodynamic bodywork was made from steel and aluminium attached to a wooden frame. The curved windows were made from Plexiglas.     ...
...n which the body is integrated into a single unit with the chassis rather than having a separate body-on-frame. The welded "Unit Body" is the predominant automobile construction technology today. ...
...ound the best recommendations are actual user testimonials. Most of the rust is on the undercarriage and frame, so I am looking for something I can easily spray on before painting or undercoating. How...
... blown from being stored). This car is not folding in half but it does need: 1/4's, fenders, floor pans, frame rails, etc. It has a nice trunk floor, hood , trunk lid and even the doors can be used wi...
Besides a complete frame off restoration and sand blasting the rust, what is the best way to treat hard to reach rust on the frame? Has anyone tried any of the spray on 'rust converters'? Do any of th
... than the left, and very close to (less than 1/8' from) a structural cross-member that seems like it's a frame-stiffener? There's another cross-member on the left. Is the car just tremendously out o...
... it means to build truck bodies. A friend of mine who in interested in antique cars told me that the old frames where made out of wood but I cannot visualize this....
...ation of my 46 Willys, I have payed plenty for shipping, but this won takes the cake. I got a windshield frame, including glass, from a fellow in CO andit only cost me $50 for shipping VIA UPS, me thi...
...ompletely professionaly restored 1957 Chevrolet CONVERTIBLE. Houston Texas. ** 25 miles since a complete frame off restoration ** Power pack V-8 with Harden valves for use with unleaded gasoline ** Po...
Does anyone know of any online license plate frame vendors. I'm looking for the old die-cast metal dealer frames. (Preferably Plymouth) Search engines seem to turn up nothing but vanity frame makers a
...w else to describe it: It is a replica of a 1955 Ford Thunderbird, that has a fiberglass body on a steel frame; the car is approximately 6 feet long and 18-24 inches wide. These were produced in 1955 ...
...st retired and now have time to restore it to street quality again. Have a lot of surface rust on I-beam frame, drive shaft, differential, suspension etc. I can scrape and wire brush, but a surface ru...
Does anyone know where I can find information/directions on how to remove the windshield frame from my 1930 Model A coupe in order to take it in to have the windshield glass replaced? please reply d
...round give me a try . My only stipulation is a good solid body and will consider anything from shell and frame to rolling chassis to turnkey.( years 1925-1972)...
I need a Grill for my 34' Hupmobile 417W. I could also use a windshield frame and some more hubcaps. Original or reproductions
Where is the locaton of the Frame Number (VIN, today) On Model T's, Model A 's . Is it stamped into the frame or is there a plate rivited on? Thank you
...on removing the windshield (into which I managed to put lots of cracks) I found that a large area of the frame above the drivers side has rusted away. I had expected some damage, as the entire windshe...
...the original engine and there is an additional engine available. It even comes with a rebuilt Nova front frame assembly. For detailed information contact Danny at DRE Auto body 727-525-4540....
...h?) and it'll run again with some tinkering, but the brakes were going bad. Decent body, convertible top frame (no canvas top), California black plates, some extra parts, clean underbody and floors, l...
.... Was in an accident all damanged panels replaced including front shroud. Minor dammage to outriggers on frame. Motor out on stand rebuilt many years ago never put back in. The car is in Texas. Call f...
... I'd like to convert it over to straight- drive. How much trouble is this? Does the strange-oid X-shaped frame interfere with mounting a later-model 4-speed? Has anyone out there actually done this? I...
Page: 1

Copyright © 2006 - Nov 2008 Antique Cars Club